최신 덤프

VUE/Prometric 시험번호: 640-821
시험이름: Introduction to Cisco Networking Technologies
Q&A: 97 Q&As
가격(달러): $ 79.00 $ 29.00 USD

640-821 합격률 100%
1.Refer to the exhibit. A person is trying to send a file from a host on Network A of the JAX Company to a
server on Network Z of the XYZ Company. The file transfer fails. The host on Network A can communicate
with other hosts on Network A. Which command, issued from router RTA, would be the most useful for
troubleshooting this problem?
A. show flash:
B. show history
C. show version
D. show interfaces
E. show controllers serial
Answer: D
2. Which Layer 4 protocol is used for a Telnet connection?
A. IP
B. TCP
C. UDP
D. ICMP
E. DNS
Answer: B

640-821합격률 100% ,최신 덤프 입니다 . 외우면 합격할수 있습니다 .
VUE/Prometric 시험번호: 640-821
시험이름: Introduction to Cisco Networking Technologies
Q&A: 97 Q&As
1. Which Layer 4 protocol is used for a Telnet connection?
A. IP
B. TCP
C. UDP
D. ICMP
E. DNS
Answer: B
2. What is the subnet address of 172.16.159.159/22?
A. 172.16.0.0
B. 172.16.128.0
C. 172.16.156.0
D. 172.16.159.0
E. 172.16.159.128
F. 172.16.192.0
Answer: C
3. What is the purpose of flow control?
A. to ensure data is retransmitted if an acknowledgment is not received
B. to reassemble segments in the correct order at the destination device
C. to provide a means for the receiver to govern the amount of data sent by the sender
D. to regulate the size of each segment
Answer: C
4. During the boot sequence, a 2600 series router needs to locate and load an operating system. What is
the default order the router uses to find an operating system?
A. Flash, TFTP server, ROM
B. Flash, TFTP server, RAM
C. Flash, NVRAM, TFTP server
D. ROM, TFTP server, Flash
E. Flash, ROM, TFTP server
Answer: A

시험이름: Cisco Certified Network Associate(CCNA)
Q&A: 156 Q&As
640-802 10월 15일 업데이트 됐던 덤프 이고 최신 덤프 입니다 . 이덤프 필요하시는 사람이 나에게 연락해 주세요 ,그리고 무료 다운로드 할수 있습니다 ,자료로 참고할수 있습니다 . 640-802 지금 까지는 떨어지는 사람이 없으니까 정말 좋은 덤프 입니다 . PDF버전 도 있고 시물레이션 버전도 있습니다 . 그리고 640-802 다 20달러 할인해 드립니다 .일년동안 무료 업데이트 제공할것입니다 .
이하는 640-802 시험덤프 입니다 .
Exhibit:

Answer:Router>enable
Router#config terminal
Router(config)#hostname Gotha
Gotha(config)#enable secret mi222ke
Gotha(config)#line console 0
Gotha(config-line)#password G8tors1
Gotha(config-line)#exit
Gotha(config)#line vty 0 4
Gotha(config-line)#password dun63lab
Gotha(config-line)#login
Gotha(config-line)#exit
Gotha(config)#interface fa0/0
Gotha(config-if)#ip address 209.165.201.4 255.255.255.224
Gotha(config-if)#no shutdown
Gotha(config)#interface s0/0/0
Gotha(config-if)#ip address 192.0.2.190 255.255.255.240
Gotha(config-if)#no shutdown
Gotha(config-if)#exit
Gotha(config)#router rip
Gotha(config-router)#version 2
Gotha(config-router)#network 209.165.201.0
Gotha(config-router)#network 192.0.2.176
Gotha(config-router)#end
Gotha#copy run start

10월 15일 640-811 업데이트 됐습니다 .합격률 100%
시험이름: Interconnecting Cisco Networking Devices
Q&A: 120 Q&As
가격(달러): $ 79.00 $ 59.00 USD (대강 76700 원KRW)
버전 v3.21
640-811 덤프를 샀는데 만약 시험에 합격하지 못하면 환불할 수 있나요? 시험 비용과 덤프 비용을 모두 전액 환불 가능한가요?그리고 시험 적중률이 얼마인가요? 그럼 지금부터 여러분들이 궁금해 하시는 이런 문제들에 대하여 한 번 이야기해볼까요?
미가씨: 그 회사의 덤프를 사고 시험에서 떨어진다면 어떻하죠? 돈을 지불하면서까지도 얻고 싶은 효과를 얻지 못하면 어쩌죠? 그리고 합격률은 얼마나 되나요?
김영섬씨: 그러게, 시험에서 떨어지면 돈을 낭비할 뿐 만 아니라 정신적인 상처도 받을 수 있잖아요. 합격률이 높다면 비싸도 살 만 하다고 생각하지만요.
진어씨: 그러게요, 합격한다면 돈이 많이 들어도 기분이 좋잖아요.

답변 : 우선 저희 회사의 합격률은 100%입니다. 그리고 떨어진다면 전액
환불해드려요. 하지만 덤프 비용만 환불해드려요. 시험비용까지 환불해드리면 회사가 불쌍하잖아요.ㅠ_ㅠ 시험 비용은 환불해 드릴수 없어요.
김영섬씨: 덤프 비용은 환불이 된다고 하니 살만하다는 생각이 들어요. 다음 주에 시험이 있지만…시험은 제가 노력하기에 따라 달린일이니까요.
Refer to the exhibit. What can be determined from the output shown?
A.

A.The JaxSwitch1 switch is using VTP.
B.This is the only switch in the LAN topology.
C.The JaxSwitch1 switch is not the root switch.
D.The link to the root bridge is through a 1 Gbps connection.
E.Spanning Tree Protocol is disabled on the JaxSwitch1 switch.
Correct:C

합격률 100%의 덤프 640-721 무료 다운로드 할수 있습니다 .
무료 다운로드 홈페이지 바로가기 : http://www.killtest.co.kr/CCNA/640-721.asp
1. For the following items ,which one correctly describes fading?
A. A function of the frequency and should be provided in the cable specification by the vendor.
B. Another signal source is producing energy on the channel in which you are trying to operate.
C. A time-varying change in the path loss of a link with the time variance governed by the movement of
objects in the environment, including the transmitter and receiver themselves.
D. The desired signal reaches the receiving antenna via multiple paths, each of which has a different
propagation delay and path loss.
Answer: C
2. Observe the following statements, which limitation applies to the use of the Cisco WLAN Solution
Management over Wireless feature?
A. Read-write access is not available; only read-only access is supported.
B. Controllers must be managed using only secure protocols (that is, SSH and HTTPS), not nonsecure
protocols (that is, HTTP and Telnet).
C. Uploads and downloads from the controller are not allowed.
D. Wireless clients can manage other controllers however not the same controller and AP to which the
client is associated.
Answer: C
3. As a network technician ,you must know Cisco WiSMs . Up to how many Cisco WiSMs are supported in
a single mobility group operating under v5.0 code?
A. 16
B. 12
C. 24
D. 5
Answer: B
4. You work as a network technician at Cisco.com, read this subject carefully ,then answer the question.
The existing Cisco Unified Wireless Controller is running v5.0 code for both the controllers and the Cisco
WCS. A controller has been configured with an appropriate rogue rule condition to report discovered APs
The safer , easier way to help you pass any IT exams.
3 / 10
to the Cisco WCS. What default alarm level is used to display all rogue APs in the Alarm Summary?
A. Major
B. Critical
C. Flash
D. Minor
Answer: D
5. What are the four types of wireless networks?(Choose four)
A. Wireless PAN
B. LAN
C. MAN
D. VLAN
E. WAN
Answer: ABCE
6. Cisco Client Management Frame Protection is running on a mobility group with two controllers. For the
following options ,which two MFP requirements protect the network? (Choose two.)
A. requires the use of a nonbroadcast SSID
B. requires CCXv5
C. implements the validation of wireless management frames
D. forces clients to authenticate, using a secure EAP method only
Answer: BC
7. What happens when client exclusion is enabled with a timeout value of zero ?
A. Clients are excluded indefinitely.
B. Client exclusion is disabled.
C. Clients are never excluded.
D. Clients must be explicitly included by specifying the MAC address.
Answer: A
The safer , easier way to help you pass any IT exams.
4 / 10
8. The central office is currently using a combination of 4400 and 2100 series WLAN controllers running
v4.2 and a variety of LWAPP-enabled access points servicing both 2.4 GHz and 5 GHz. The WLAN
deployment has been extended to each remote office by implementing a 526 WLAN controller running
v4.1 and several 521 access points. Wireless client deployment uses EAP-TLS authentication by use of a
centralized RADIUS server plus 802.11n for performance. After the first remote office deployment, remote
office users complain that they are not connecting via 802.11n.
Which will most likely cause this problem?
A. The 521 AP does not support 5 GHz, which prohibits 802.11n.
B. The 521 AP and 526 WLAN controllers do not support AES, which prohibits 802.11n.
C. The 526 WLAN controller does not support external authentication via RADIUS, prohibiting
authentication.
D. The 526 WLAN controller does not support 802.11n with either v4.1 or v4.2.
Answer: D
9. How do the characteristics that are available on the Cisco WCS for Linux version differ from those of
the Cisco WCS for Windows version?
A. Cisco WCS for Linux is required for deployments.
B. Assuming that there are no differences in hardware, a Cisco WCS for Linux can support up to 750
wireless LAN controllers. A Cisco WCS for Windows can support up to 250 wireless LAN controllers.
C. Cisco WCS for Windows includes support for Cisco Spectrum Expert clients. Cisco WCS for Linux
does not support Cisco Spectrum Expert clients.
D. There are no differences in features between the Linux and Windows versions of Cisco WCS.
Answer: D
10. What is the typical maximum range of a wireless PAN?
A. 45 feet
B. 50 feet.
C. 55 feet
D. 60 feet
Answer: B
The safer , easier way to help you pass any IT exams.
5 / 10
11. Which one of the following CLI commands displays the controller configuration in a way that is similar
to the way that it is shown on Cisco IOS routers?
A. show run-config
B. show config
C. show run config
D. show running-config
Answer: D
12. Observe the following attacks, which two does Management Frame Protection help to mitigate?
(Choose two.)
A. War Driving
B. Man-in-the-Middle
C. Eavesdropping
D. Denial of Service
Answer: BD
13. Which device(s) will Lightweight access points send control traffic to?
A. The Wireless Control System.
B. Other access points.
C. The Wireless Controller.
D. Lightweight access points don’t send control traffic.
Answer: C
14. For the following elements ,which three define the 802.11n implementation of MIMO? (Choose three.)
A. Channel Bonding
B. Maximal Ratio Combining
C. Spatial Multiplexing
D. Transmit Beam Forming
Answer: BCD
The safer , easier way to help you pass any IT exams.
6 / 10
15. True or false: A wireless PAN consumes little power from small handheld computer devices.
A. True
B. false
Answer: A
16. In the AP Layer 3 controller discovery process, after the LWAPP Discovery Request is broadcast on a
local subnet, which action will AP take next?
A. Send an LWAPP response to the master controller if known.
B. Send an LWAPP discovery request to controllers learned via OTAP if operational.
C. Wait 5 seconds and resend a Discovery Request to the local subnet.
D. Determine whether the controller responses are the primary controller.
Answer: B
17. Which three values will be used to calculate Effective Isotropic Radiated Power? (Choose three.)
A. antenna bandwidth
B. antenna gain
C. cable loss
D. transmission power
Answer: BCD
18. When importing a single campus map into the Cisco WCS 5.0, which four file formats will be used?
(Choose four.)
A. BMP
B. PNG
C. GIF
D. JPEG
E. JPG
Answer: BCDE
19. You are a network engineer at Cisco.com, When creating a wireless profile in the Cisco ADU and you
The safer , easier way to help you pass any IT exams.
7 / 10
have selected the WPA/WPA2/CCKM radio button option, what other decision will you make and then
configure on this same screen?
A. the SSID of the wireless client
B. the length and value of the pre-shared key
C. the EAP type to be used for authentication
D. the encryption type
Answer: C
20. What is a common standard for wireless LANs?(Choose two)
A. IEEE 802.11
B. IEEE 802.3z
C. Wi-Fi
D. IEEE 802.16.
Answer: AC
21. Match the proper relationship between interface description and the appropriate.
1. Designed to be analogous to VLANs for wireless LAN client device
2. The only port that is active when the controller is in boot mode
3. This interface is the only consistently*pingable* in-band interface IP address on the Cisco WLC
4. Used for Layer 3 communications between the Cisco WLC and the lightweight access points
5. Used to support mobility management. DHCP relay, and guest web authencation.
I.AP Manager
II.Dynamic
III.Management
IV.Service Port
V.Virtual
A. I-4,II-1,III-5,IV-2,V-3
B. I-4,II-1,III-2,IV-5,V-3
C. I-4,II-1,III-5,IV-3,V-2
D. I-4,II-1,III-2,IV-3,V-5
The safer , easier way to help you pass any IT exams.
8 / 10
Answer: A
22. Which roaming situation using controllers in a Cisco Unified Wireless Network requires a client by use
of WPA2 with PKC to reauthenticate to the network?
A. A wireless client roams to another AP on the same controller.
B. A wireless client roams to another AP after being out of range of the network for 2 minutes.
C. A wireless client roams to another AP on a different controller in the same mobility domain.
D. A wireless client roams to another AP on a controller in a different mobility domain.
Answer: D
23. Which three methods of authentication are usually used in enterprise wireless networks? (Choose
three.)
A. AES
B. CCKM
C. PEAP
D. EAP-FAST
E. EAP-TLS
Answer: CDE
24. ou are a network technician at Cisco.com ,study the options carefully.A client is attached to the Cisco
Unified Wireless network by use of controllers. When the client is using WPA2 and EAP authentication,
where are the wireless encryption keys located during the active user session? (Choose two.)
A. on the client
B. on the Cisco WCS
C. on the RADIUS server
D. on the access point
Answer: AD