최신 덤프

시험이름: CCIP Configuring BGP on Cisco Routers (BGP)
Q&A: 121 Q&As
가격(달러): $29.00 USD
업그레이트: Mar-16-2010
무료 시험문제 먼저 보기:
1.What are two purposes of the BGP scan-time command? (Choose two.)
A.to tune the BGP process which walks the BGP table and confirms the reachability of next hops
B.to allow faster detection of downed BGP peers
C.to improve BGP convergence time
D.to tune the BGP update interval
E.to decrease the effects of unstable routes by increasing the route suppression time
Correct:A C
2.Which command is used to configure the external, confederation-wide AS number?
A.router(config)#router bgp {as-number}
B.router(config-router)#bgp confederation peers {as-number}
C.router(config-router)#bgp confederation identifier {as-number}
D.router(config-router)#bgp cluster-id {as-number}
E.router(config-router)#neighbor {ip address} remote-as {as-number}
Correct:C
3.When creating iBGP multipaths which three criteria must be met by multiple paths to the same
destination? (Choose three.)
A.Router IDs must be the same on all routers.
B.Each destination must have a different next-hop address.
C.The destination AS-number must be different for each destination.
D.Multi-exit discriminator attributes must be the same on all paths.
E.Interior Gateway Protocol distance must be identical on each path.
Correct:B D E
4.Which two of these statements about hierarchical route reflectors are correct? (Choose two.)
A.A route reflector can be a client of another route reflector.
B.Each cluster within the hierarchy can only contain one route reflector.
C.The hierarchy can be as deep as needed.
D.A route reflector can have clients in different clusters.
E.Hierarchical route reflectors are set up using three levels (access, distribution, and core layers).
Correct:A C
5.What can cause a single sourced iBGP route not to be selected as the best route?
A.The BGP MED is 0.
B.The BGP next-hop is unreachable.
C.The BGP origin is incomplete.
D.The BGP weight is 0.
E.The BGP local preference is 0.
F.BGP synchronization is disabled.
Correct:B

시험이름: Building Cisco Multilayer Switched Networks
Q&A: 227 Q&As
업그레이트: Mar-16-2010
시험문제:

1. Which three WLAN statements are true? (Choose three.)
A. A lightweight AP receives control and configuration from a WLAN controller to which it is associated.
B. A WLAN client that is operating in half-duplex mode will delay all clients in that WLAN.
C. Ad hoc mode allows mobile clients to connect directly without an intermediate AP.
D. Another term for infrastructure mode is independent service set (IBSS).
E. The Aironet 1230 access point is an example of an access point that operates solely as a lightweight
access point.
F. WLANs are designed to share the medium and can easily handle an increased demand of channel
contention.
Answer: ABC
2. Which statement is true about IP telephony calls?
A. A Voice over IP (VoIP) packet consists of the voice payload, IP header, TCP header, RTP header, and
Layer 2 link header.
B. The voice carrier stream uses H.323 to set up, maintain, and tear down call endpoints.
C. Call control signaling uses Real-Time Transport Protocol (RTP) packets that contain actual voice
samples.
D. The sum of bandwidth necessary for each major application, including voice, video, and data, should
not exceed 75 percent of the total available bandwidth for each link.
Answer: D
3. Which three statements are true about the voice VLAN feature on a Catalyst 2950 switch? (Choose
three.)
A. The CoS value is trusted for 802.1p or 802.1q tagged traffic.
B. The voice VLAN feature is disabled by default.
C. The IP phone accepts the priority of all tagged and untagged traffic and sets the CoS value to 4.
D. When the voice VLAN feature is enabled, all untagged traffic is sent according to the default CoS
priority of the port.
E. PortFast is automatically disabled when a voice VLAN is configured.
F. The default CoS value for incoming traffic is set to 0.
Answer: BDF
4. In what three ways is QoS applied in the campus network? (Choose three.)
A. No traffic marking occurs at the core layer. Layer 2/3 QoS tags are trusted from distribution layer
switches and used to prioritize and queue the traffic as it traverses the core.
B. IP precedence, DSCP, QoS group, IP address, and ingress interface are Layer 2 characteristics that
are set by the access layer as it passes traffic to the distribution layer. The distribution layer, once it has
made a switching decision to the core layer, strips these off.
C. MAC address, Multiprotocol Label Switching (MPLS), the ATM cell loss priority (CLP) bit, the Frame
Relay discard eligible (DE) bit, and ingress interface are established by the voice submodule (distribution
layer) as traffic passes to the core layer.
D. The distribution layer inspects a frame to see if it has exceeded a predefined rate of traffic within a
certain time frame, which is typically a fixed number internal to the switch. If a frame is determined to be in
excess of the predefined rate limit, the CoS value can be marked up in a way that results in the packet
being dropped.
E. The access layer is the initial point at which traffic enters the network. Traffic is marked (or remarked)
at Layers 2 and 3 by the access switch as it enters the network, or is “trusted” that it is entering the
network with the appropriate tag.
F. Traffic inbound from the access layer to the distribution layer can be trusted or reset depending upon
the ability of the access layer switches. Priority access into the core is provided based on Layer 3 QoS
tags.
Answer: AEF
5. Which two Aironet enterprise solution statements are true? (Choose two.)
A. A Cisco Aironet AP handles the transmission of beacon frames and also handles responses to
probe-request frames from clients.
B. A Cisco Aironet solution includes intelligent Cisco Aironet access points (APs) and Cisco Catalyst
switches.
C. In the Cisco Aironet solution, each AP is locally configured by the use of either a web interface or the
command line interface.
D. The Cisco Aironet AP handles real-time portions of the LWAPP protocol, and the WLAN controller
handles those items which are not time sensitive.
E. Virtual MAC architecture allows the splitting of the 802.11 protocol between the Cisco Aironet AP and a
LAN switch.
Answer: AD

시험이름: Designing Cisco network Service Architectures (ARCH)
Q&A: 219 Q&As
업그레이트: Mar-16-2010
1. You are the network consultant from Cisco.com. Please point out which Layer 2 access designs does
not support VLAN extensions?
A. FlexLinks
B. loop-free U
C. looped square
D. looped triangle
Answer: B
2. Which typical enterprise campus requirement ensures that the network supports the required
applications and that data flows within the required time frames?
A. availability
B. performance
C. functionality
D. manageability
Answer: C
3. You are the Cisco Network Designer in Cisco.com. Which of these is a Layer 2 transport architecture
that provides packet-based transmission optimized for data based on a dual ring topology?
A. Dynamic Trunking Protocol
B. Resilient Packet Ring
C. Synchronous Digital Hierarchy
D. Coarse Wave Division Multiplexing
Answer: B
4. What two choices can you make when redundancy is required from a branch office to a regional office?
(Choose two.)
A. multiple Frame Relay PVCs
B. dual Wan links to the regional office
C. dual Wan links to another branch office
D. single links - one to the regional office and one to another branch office
Answer: BD
5. Which one is not the feature of the Cisco Unified Wireless Network architecture?
A. network unification
B. remote access
C. mobility services
D. network management
Answer: B

시험이름: Composite Exam
Q&A: 229 Q&As
업그레이트: Mar-16-2010
시험문제:
1. If no metric is specified for the routes being redistributed into IS-IS, what metric value is assigned to the
routes?
A. 0
B. 1
C. 10
D. 20
Answer:A
2. Which three restrictions apply to OSPF stub areas? (Choose three.)
A. No virtual links are allowed.
B. The area cannot be a backbone area.
C. Redistribution is not allowed unless the packet is changed to a type 7 packet.
D. The area has no more than 10 routers.
E. No autonomous system border routers are allowed.
F. Interarea routes are suppressed.
Answer: ABE
3. Refer to the exhibit. Which two statements are true about the partial configuration that is provided.
(Choose two.)

A. All the configured neighbors are in autonomous system 100.
B. The peer group shortens the IBGP configuration.
C. The peer group shortens the EBGP configuration.
D. Only the outgoing filters are applied to BGP updates.
E. Three AS-path filters are applied to each BGP neighbor.
Answer:AB
4. Refer to the exhibit. Which two statements are correct? (Choose two.)

A. All six routes will be installed in the routing table.
B. Two routes will be installed in the routing table.
C. Four routes will be installed in the routing table.
D. All the routes were redistributed into BGP from an IGP.
E. All the routes were originated by BGP with the network command.
Answer: CD
5. Which three IP multicast related statements are true? (Choose three.)
A. Multicast addresses 224.0.1.0 through 238.255.255.255 are called globally scoped addresses. They
are used to multicast data between organizations and across the Internet.
B. The multicast address 224.0.0.1 is a globally scoped address that has been reserved for the Network
Time Protocol (NTP) by the IANA.
C. Multicast addresses 239.0.0.0 through 239.255.255.255 are called limited scope addresses. They are
constrained to a local group or organization.
D. Multicast addresses 224.0.0.5 and 224.0.0.6 are limited scoped addresses that have been reserved for
OSPF.
E. Multicast addresses 224.0.0.0 through 224.0.0.255 are used for network protocols on local LAN
segments. Because they are always transmitted with a Time to Live (TTL) of 1, they are never forwarded
by a router.
Answer:ACE

참고글:http://kr.blog.yahoo.com/k5k5k123@ymail.com 인증에 대해 더 많이 볼수 있고 다른 재밋는 글도 많습니다.

시험이름: Building Scalable Cisco Internetworks
Q&A: 247 Q&As
업그레이트: Mar-16-2010
시험문제:
1. What are the two reasons for the appearance of 0.0.0.0 as the next hop for a network in the show ip
bgp command output? (Choose two.)
A. The network was originated via redistribution of an interior gateway protocol into BGP.
B. The network was defined by a static route.
C. The network was originated via a network or aggregate command.
D. The network was learned via EBGP.
E. The network was learned via IBGP.
Answer: AC
2. If no metric is specified for the routes being redistributed into IS-IS, what metric value is assigned to the
routes?
A. 0
B. 1
C. 10
D. 20
Answer: A
3. Refer to the exhibit. Which three statements accurately describe the result of applying the exhibited
route map? (Choose three.)

A. The map prohibits the redistribution of all type 2 external OSPF routes with tag 6 set.
B. The map prohibits the redistribution of all type 2 external OSPF routes.
C. The map redistributes into EIGRP all routes that match the pfx prefix list and the five metric
values40000, 1000, 255, 1, and 1500.
D. The map prohibits the redistribution of all external OSPF routes with tag 6 set.
E. All routes that do no match clauses 10 and 20 of the route map are redistributed with their tags set to 8.
F. The map permits the redistribution of all type 1 external OSPF routes.
Answe:AEF
4. Which three restrictions apply to OSPF stub areas? (Choose three.)
A. No virtual links are allowed.
B. The area cannot be a backbone area.
C. Redistribution is not allowed unless the packet is changed to a type 7 packet.
D. The area has no more than 10 routers.
E. No autonomous system border routers are allowed.
F. Interarea routes are suppressed.
Answe:ABE
5. Into which two types of areas would an area border router (ABR) inject a default route? (Choose two.)
A. the autonomous system of a different interior gateway protocol (IGP)
B. area 0
C. totally stubby
D. NSSA
E. stub
F. the autonomous system of an exterior gateway protocol (EGP)
Answer: CE

시험이름: Building Cisco Remote Access Networks (BCRAN)
Q&A: 244 Q&As
가격(달러): $ 59.00 $ 29.00 USD
시험문제:

시험이름: Cisco IP Telephony(CIPT)
Q&A: 84 Q&As
시험문제:
1. Which two of these events describe the relationship of an IP Phone to its secondary Cisco
CallManager?(Choose two.)
A. IP Phone sends a TCP keepalive message every 30 seconds.
B. IP Phone sends a TCP keepalive message every 60 seconds.
C. IP Phone sends a TCP connect message.
D. IP Phone registers with secondary when primary is unavailable.
E. IP Phone registers with primary when secondary is unavailable.
F. IP Phone registers with all CallManagers initially including secondary.
Answer:CD
2. An auto parts retailer would like their service counter representatives to be able to assist both walk-up
customers and telephone customers. Each store has six service counter representatives. Which call
distribution algorithm will allow each service counter representative to provide the best customerservice?
A. Top Down
B. Circular
C. Longest Idle Time
D. Broadcast
Answer:D
3. An auto parts retailer would like their service counter representatives to assist both walk-up customers
and telephone customers. Each store has six service counter representatives. Walk-up customers
frequently engage allthe counter representatives and management is concerned that telephone customer
business is being lost. From the list below, choose the appropriate call distribution algorithm and the
appropriate call forwardingtreatment which will allow each store to provide the best customer service.
(Choose two.)
A. When hunting is exhausted, apply CFB and CFNA to the DN for the warehouse order puller.
B. There is no need to configure CFB or CFNA; when hunting is exhausted, the call will automatically be
routedto the warehouse order puller.
C. Top Down
D. Circular
E. Longest Idle TimeF. Broadcast
Answer:AF
4. You are working with a customer to develop the methodology to secure IP Phones at their new
research facility.They will be providing IP Phones in their lobby for vendor and guest use. Which two of
these IP Phone hardening methods should be applied to these devices? (Choose two.)
A. Enable GARP.
B. Disable PC port on phone.
C. Use signed IP phone firmware.
D. Disable the Directory button.
E. Disable the Services button on the IP phone.
Answer:BC
5. Which three options can you use to assign a softkey template? (Choose three.)
A. Device > Phone Configuration
B. Device > Device Settings > Device Profile
C. Service > Service Parameters
D. System > Device Defaults Configuration
E. System > Device Pool Configuration
F. System > Enterprise Parameters
Answer:ABE

시험이름: CCIP BGP + MPLS Exam (BGP + MPLS)
Q&A: 94 Q&As
업그레이트: Jan-15-2010

시험문제:

1.Based on the network diagram shown in the exhibit, both R5 and R6 are clients of the R2 RR.
When the 10.0.0.0/8 iBGP update from R3 is received by the R2 RR, which router(s) will R2 reflect
the update to?

A.R1 only
B.R5 and R6
C.R5, R6 and R1
D.R4, R5 and R6
E.R4, R5, R6 and R1
F.to no other router
Correct:C
2.Based on this configuration, which two peering router neighbor statements are correct?
(Choose two.)router bgp 50001 neighbor 192.168.1.1 remote-as 50001 neighbor 10.1.1.1 remote-as
50002 neighbor 10.1.1.1 local-as 50003 ! output omitted
A.EBGP - neighbor 10.1.1.2 remote-as 50003
B.EBGP - neighbor 10.1.1.2 remote-as 50001
C.EBGP - neighbor 10.1.1.2 remote-as 50001 and neighbor 10.1.1.2 local-as 50003
D.IBGP - neighbor 192.168.1.2 remote-as 50001
E.IBGP - neighbor 192.168.1.2 remote-as 50003
F.IBGP - neighbor 192.168.1.2 remote-as 50003 and neighbor 192.168.1.2 local-as 50001
Correct:C D
3.LAB

Correct:
4.Which two statements about a transit AS are correct? (Choose two.)
A.A transit AS has eBGP connection(s) to only one external AS.
B.Routes between ASs are always exchanged via eBGP.
C.A transit AS uses an IGP like OSPF or ISIS to propagate the external networks within the transit AS.
D.Core routers within a transit AS normally use default routing to reach the external networks.
E.iBGP sessions can be established between non directly connected routers.
Correct:B E
5.Refer to the exhibit and the following connectivity requirements. How many different VRFs are
required? Sites CE1A, CE1B, CE1C, and CE1D require connectivity among them. Sites CE2A and
CE2B require connectivity between them. Site CE12A requires connectivity to sites CE1A, CE1B,
CE1C, CE1D, and CE12B. Site CE12B requires connectivity to sites CE2A, CE2B, and CE12A.

A.2 VRFs
B.3 VRFs
C.4 VRFs
D.6 VRFs
E.8 VRFs
F.10 VRFs
Correct:C
출처(참고자료):http://kr.blog.yahoo.com/k5k5k123@ymail.com

시험이름: Implementing Secure Converged Wide Area Networks
Q&A: 120 Q&As
업그레이트: Jan-15-2010
시험문제:

1. What are three objectives that the no ip inspect command achieves? (Choose three.)
A. removes the entire CBAC configuration
B. removes all associated static ACLs
C. turns off the automatic audit feature in SDM
D. denies HTTP and Java applets to the inside interface but permits this traffic to the DMZ
E. resets all global timeouts and thresholds to the defaults
F. deletes all existing sessions
Answer: AEF
2. Which three features are benefits of using GRE tunnels in conjunction with IPsec for building site-to-site
VPNs? (Choose three.)
A. allows dynamic routing over the tunnel
B. supports multi-protocol (non-IP) traffic over the tunnel
C. reduces IPsec headers overhead since tunnel mode is used
D. simplifies the ACL used in the crypto map
E. uses Virtual Tunnel Interface (VTI) to simplify the IPsec VPN configuration
Answer: ABD
3. Which three IPsec VPN statements are true? (Choose three.)
A. IKE keepalives are unidirectional and sent every ten seconds.
B. IKE uses the Diffie-Hellman algorithm to generate symmetrical keys to be used by IPsec peers.
C. IPsec uses the Encapsulating Security Protocol (ESP) or the Authentication Header (AH) protocol for
exchanging keys.
D. Main mode is the method used for the IKE phase two security association negotiations.
E. Quick mode is the method used for the IKE phase one security association negotiations.
F. To establish IKE SA, main mode utilizes six packets while aggressive mode utilizes only three packets.
Answer: ABF
4. Which three statements are true about Cisco IOS Firewall? (Choose three.)
A. It can be configured to block Java traffic.
B. It can be configured to detect and prevent SYN-flooding denial-of-service (DoS) network attacks.
C. It can only examine network layer and transport layer information.
D. It can only examine transport layer and application layer information.
E. The inspection rules can be used to set timeout values for specified protocols.
F. The ip inspect cbac-name command must be configured in global configuration mode.
Answer: ABE
5. Which two statements about common network attacks are true? (Choose two.)
A. Access attacks can consist of password attacks, trust exploitation, port redirection, and
man-in-the-middle attacks.
B. Access attacks can consist of password attacks, ping sweeps, port scans, and man-in-the-middle
attacks.
C. Access attacks can consist of packet sniffers, ping sweeps, port scans, and man-in-the-middle attacks.
D. Reconnaissance attacks can consist of password attacks, trust exploitation, port redirection and
Internet information queries.
E. Reconnaissance attacks can consist of packet sniffers, port scans, ping sweeps, and Internet
information queries.
F. Reconnaissance attacks can consist of ping sweeps, port scans, man-in-middle attacks and Internet
information queries.
Answer: AE